Ontario Agriculture

The network for agriculture in Ontario, Canada

I almost made my first round with my R52 Gleaner, but didn't quite make it.
It started out well, ran a moisture test from the front headland at under 14%. Then I started adjusting the concave to get a better sample. Stopping every 100 ft to check to see how much grain I was throwing over. Opened up the fan damper, tightened up the concave again, adjusted the sieve. Still a bit of chaff and heads in the bin, but Beacher Wheat is hard to harvest. Now starting to put some material through this machine, running about 3.8MPH, rebuilt header feeding well. Starting to fiddle with the monitors to learn how they work.
Then all of a sudden the auger in the header is at a standstill. The drive chain has come off the sproket.

There is always cause and effect, I was a bit rash in thinking the chain was the cause, no such luck. It was the effect.
In rebuilding the header, i missed replacing a single washer over a simple eyelette that adjusts the auger position. As a result the eyelet opened up, the auger moved back and was jamming into the stripper bar. No big damage, but not something that gets fixed by putting the chain back on.
I flipped through the manual a few times before I realized what was the source of my angst. Drive to the front of the field and unload, I have some repair work to do.

Started to unload, then had to shut off the unloader to position myself a bit further from the wagon. This R52 is a lot bigger than my old MF540 and its going to take a few rounds to get used to the length of this unload auger. But it wouldn't start again. Damn electronics! Now I am tracing the wiring diagrams, why won't this auger engage?
Drive to the yard. Now I have more to fix.

First I need this auger emptied, and I don't want to drain it through the clean out, there must be 100 bushels in the bin. All the wires look good, but the clutch will not engage. Problem is, with the grain loaded auger the metal dog that goes in front of the sensor for detedting the auger position, has moved just far enough the sensor is not made. Sollution, place a piece of metal over the sensor and everything works. Of course it took and hour and a half to figure this out.

Now I can move my attention to the plugged header. I love my Gleaner. Within 20 min all the damaged parts are off, and repaired. 20 more minutes back on and modified to prevent such a future failure (needed washer now installed). The reverser works! Hard to justify calling it a plug when it is so easy to undo. BUT the little metal cover at the center to access the fingers has gone missing. That would have plugged up my old combine, i didn't ever hear it go through this one. Back out to the field to run this straw through and see if the other repairs are good. The auger slips as I pull in to the field, lilekly need to re-adjust the slip clutch.  That ends my night.  It was getting dark, my combine needs work, and I am getting a bit tired, nothing good will come of doing any more.

Thanks to a 1/2" rain today, well timed for the tassling corn, I can take my time to make the needed replacement and repairs tonight.

 

So the wheat harvest is at a stop, the field barely touched.   But that's ok the rain is very needed.  So far today, more rain than all of June.  But surprisingly, the crops have been hanging on and are lookig good despite the drought.  I credit fall plowing.

Head high by the 4th of July!  Just need rain to take advantage of a good start.

Views: 612

Comment

You need to be a member of Ontario Agriculture to add comments!

Join Ontario Agriculture

Comment by OntAG Admin on July 5, 2012 at 10:48am

Thanks Gus,

Let us know how the wheat runs...glad you got some rain.

Take care.

Comment by Mitch Lang on July 4, 2012 at 2:53am

Your corn looks nice Gus... Must be that fertilizer you used... :)

Agriculture Headlines from Farms.com Canada East News - click on title for full story

Gophers gotcha going gaga?

With escalating gopher populations causing increasing concern for landowners across Saskatchewan, the Saskatchewan Wildlife Federation (SWF), with the support of the Saskatchewan Association of Rural Municipalities (SARM), is stepping up to offer practical assistance. Gophers are a significant cause of crop loss and land degradation, impacting the livelihood of Saskatchewan producers and landowners, according to the SEF. In response, the SWF is connecting landowners with trusted SWF members who are ready to assist in controlling gopher numbers in a responsible and ethical manner. Landowners experiencing challenges with gophers are encouraged to contact the SWF office at 306-692-8812. The SWF will then work to identify available SWF members in that area to co-ordinate arrangements directly with the landowner. All SWF members participating in this initiative carry an additional $5 million in liability coverage, and are expected to uphold the highest standards of safety, conduct and la

Attention Researchers: The BCRC Opens Call for Letters of Intent

The Beef Cattle Research Council invites letters of intent (LOIs) for research projects. The application deadline for this call is September 2, 2025,?at 11:59?PM MT. The purpose of this call is to achieve specific priorities listed in the 2025 Call for Letters of Intent – Research document (selected through consultation with industry stakeholders from the Canadian Beef Research and Technology Transfer Strategy).  Approved projects will be required to?use the industry funding to leverage additional funds from government or other funding organizations to fulfill project budgets.  Preference will be given to projects that are one to three years in duration; if the need for a longer timeframe can be clearly demonstrated, four or five-year projects may be considered. Projects will commence no earlier than May 1, 2026. Refer to the documents below for more information. All call-related information can also be found on the BCRC’s Call for Proposals webpage. Sharing or reprinting BCRC posts

Calf Auction Raises Funds for Youth

A young man from Milverton auctioned a prize calf, raising over $31,000 for Autism Ontario, inclusive sports, and milk programs, with huge support from the local community.

BFO Cow-Calf Financing Survey

BFO is soliciting feedback from Ontario cow-calf producers on the use of various financial assistance and herd financing programs through the completion of a short survey.

Moving More Lentils: Progress & Priorities in Europe

Work is underway to expand opportunities for Canadian pulses in the European Union and United Kingdom, particularly for lentils, while addressing regulatory and policy barriers that continue to impede market access.

© 2025   Created by Darren Marsland.   Powered by

Badges  |  Report an Issue  |  Terms of Service